Re: wynik testu HDD Health

> Nie sądzę. Prędzej właśnie wspomniane ustawienia w biosie albo jakieś
> uszkodzenie pamięci lub kontrolera. Ściągnij tego memtesta86+ i sprawdź.
> Program znajdziesz na google, są też wersje instalujące się na dyskietce,
> wystarczy wtedy taką dyskietkę włożyć do stacji i zrestartować komputer.
Sciągnąlem i zrobiłem tę dyskietkę. Odpaliłem. Potestowało dwie godziny,
żadnych errorów nie znalazło.

> > Pewnie uszkodziłem dysk twardy, bo restartom towarzyszy dość głośne
> > jego rozpędzanie tak jakby uprzednio był zahibernowany.
>
> Dysk możesz sprawdzić oprogramowaniem diagnostyczym ze strony producenta.
> Zobacz też, co mówi SMART (zainstaluj HDD Health).
Wyszło takie coś:
Drive model ST360021A
Drive capacity 58,6 GB
Drive serial number 3HR0TPZJ
Firmware revision 3.19
Number of cylinders 16383
Number of heads 16
Number of sectors per track 63
Number of LBA sectors 117231408
DMA support Enabled
LBA support Enabled
IORDY support Enabled
ATA software reset Not required
Overlap operation Supported
Command queuing Not supported
Interleaved DMA Not supported
Multiword DMA mode supported Mode 2 and below
PIO transfer mode supported Mode 4
Minimum Multiword DMA transfer cycle time per word 120 ns
Manufacturer's recommended Multiword DMA transfer cycle time 120 ns
Minimum PIO transfer cycle time without flow control 240 ns
Minimum PIO transfer cycle time with IORDY flow control 120 ns
ATA standard version ATA/ATAPI-5 and below
SMART feature set Supported, Enabled
Security Mode feature set Supported, Disabled
Removable Media feature set Not supported
Power Management feature set Supported
PACKET Command feature set Not supported
Write cache Supported, Enabled
Look-ahead Supported, Enabled
Release interrupt Not supported
SERVICE interrupt Not supported
DEVICE RESET command Not supported
Host Protected Area feature set Supported
WRITE BUFFER command Supported
READ BUFFER command Supported
NOP command Not supported
DOWNLOAD MICROCODE command Supported
READ DMA QUEUED and WRITE DMA QUEUED commands Not supported
CFA feature set Not supported
Advanced Power Management feature set Not supported
Removable Media Status feature set Not supported
Power-Up In Standby feature set Not supported
SET MAX security extension Supported, Disabled
Automatic Acoustic Management feature set Supported, Enabled
48-bit Address feature set Not supported
Device Configuration Overlay feature set Supported
FLUSH CACHE command Not supported
FLUSH CACHE EXT command Not supported
SMART error logging Not supported
SMART self-test Not supported
Media serial number field words Not supported
Media Card Pass Through Command feature set Not supported
Streaming feature set Not supported
General Purpose Logging feature set Not supported
WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands Not supported
WRITE DMA QUEUED FUA EXT command Not supported
World wide name Not supported
URG bit for READ STREAM DMA and READ STREAM PIO commands Not supported
URG bit for WRITE STREAM DMA and WRITE STREAM PIO commands Not supported
Time-limited Read/write feature set Not supported
Read Continuoud and Write Continuous in the Time-limited Read/write feature
set Not supported
Ultra DMA mode selected Mode 5
Ultra DMA mode supported Mode 5 and below
The time required for the SECURITY ERASE UNIT command to complete Value
not specified
Time required for Enhanced security erase unit completion Value not
specified
Master Password Revision Code Not supported
Device vendor's recommended acoustic management level 128
The current automatic acoustic management level 128
Removable Media Status Notification feature set Not supported
Enhanced security erase unit feature Not supported
The security count is expired and SECURITY UNLOCK and SECURITY ERASE UNIT
are command aborted until a power-on reset or hardware reset.
CFA Power Mode Mode 0
Maximum average RMS current 82 Milliamperes

Start/Stop Count (Power on count) 125 times
Reallocated Sectors Count 0 sectors
Power-On Hours 7927 minuties (hours)
Device Power Cycle Count 1254 times
Temperature 32 °C
Current Pending Sector Count (Unstable sectors) 0 sectors
Uncorrectable Sector Count 0 sectors
UltraDMA CRC Error Count (total) 2 errors
Write Error Rate (Multi Zone Error Rate) 0

A smart nie bardzo kumam bo jest tabela value, threshold i worst, co można
tłumaczyć wartość, granica dop, i niedopuszczalna wartość.
No więc mam kilka wartości nieźle poprzekraczanych...

Posprawdzam jeszcze na stronie Seagate.

pozdrawiam,
LN
Received on Wed Mar 2 21:15:27 2005