Autor: Tomek 'Tommy' Dębiński (tdebinski_at_poczta.onet.pl)
Data: Wed 31 Jul 2002 - 06:06:39 MET DST
> >M601 V1.3
> >MADE IN TAIWAN R.O.C.
>
> http://venus.spaceports.com/~canada/webhq/models/486vlb3/m601.html -
> może to ?
Tak to jest wlasnie to !
Wielkie dzieki nawet dostalem juz od nich opis poszczegolnych jumperow.
Ale wynika z niego ze mozna na nim puscic procesor z zegarem do 66 MHz.
A ja mam w nim DX2-80 - czyli raczej nie pojdzie.
Zreszta przesylam mini dokumentacje (ponizej)
=>View or Print jumper settings using New Courier fixed width font<=
M601 & M602 V1.3A-F 486 VESA Motherboard
- AMI BIOS ID string 40-0100-001437-00101111-080893-4386-F
- AMI BIOS ID string 40-0101-001437-00101111-080893-UMC491-F
- AWARD BIOS ID string 1990 Pheonix Technologies S-B16-V16-Foff
- 8-30 pin SIMM slots (1-64meg FPM DRAM)
- 64k-256k CACHE support in 8-28pin sockets + 2 TAG RAM socket
- 3-32bit VESA Local Bus slots
- 7-16bit ISA slots
- AMI/AWARD Modular BIOS V4.50 1993 Auto-Detect Bios
- UMC/SARC RC4018A4 Chipset
- CPU socket, uses any 486 Intel/AMD/Cyrix to 66Mhz CPU
- possibly manufactured by: -FUGU TECH ENTERPRISE CO., LTD.
-PC Chips
-COMMODORE CPTs and others
=======================================================================
If you encounter a BIOS generated 'VIRUS WARNING' when upgrading your
operating system to WIN95/98 the cause could be any of the following:
- try hitting the f8 during the boot up and go to the dos prompt,
then go to WIN95 and see what happens...if it does work then there is
a problem in the set up files themselves.
- if you cannot get WIN95 to install because of the warning type setup/?
for the other options and there is one for no detection...it will
install the files then you will have to add the hardware drivers
and stuff after manually.
- is the WIN95 a full version or the upgrade and is it on disk or cd.
If on disk they had a lot of problems with Ver:A of both series.
The 'B' version is more revised with less problems...if someone has
tried to tamper at all with the disks then it will come up with that
warning....they are formatted to 1.77meg on purpose to make it harder
to hack...but it still can be done... :-)
- another way is to copy all the disks into one directory leaving the
cab files as cabs then run setup...do this from the dos prompt.
If they have been hacked or tampered with whether disk or cd this
usually gets around it since it is reading itself and not another
drive so error correction is at a minimum level...hope this helps.
- Disabling Award BIOS v4.50g Virus Protection
This webpage explains the full procedure if you have this bios.
http://www.sysopt.com/virwarn.html
- and finally your BIOS's external cache might be incompatible.
Most 32bit OS's advise disabling all external caching during install
on older boards. The problem resides in the older BIOS versions.
Some M601 mainboards will not support WIN95's caching system with any
BIOS dated 1993 or older. Try to disable/remove the onboard cache or
buy a newer bios, BUT, try all the above procedures first.
Once WIN95 is installed try enabling/installing the cache and reboot.
=======================================================================
Purpose Location Purpose Location
------------------------------------------------------------------------
External battery JP1 Power LED & keylock JP10
Speaker JP11 Turbo LED JP12
Reset switch JP13 Turbo switch JP14
Power 9000 VGA card installed JP23 2-3
All other video cards JP23 1-2
Battery JP1
----------------------------
Rechargeable 2-3
Clear CMOS 3-4 (short for 3-4secs only with power off)
External installed (pin1 VDD 3.6volt lithium, pin4 ground)
=======================================================================
VESA Bus Wait States JP15
-----------------------------
0 W/S 25MHZ OPEN
1 W/S 33MHZ OPEN
2 W/S 50MHZ 1-2
=======================================================================
CPU Selector settings JP16 JP17
---------------------------------------------
486DX/DX2 1-2,3-4 1-2
486SX(Cyrix 486) 2-3 open
P23N 1-2,3-4 2-3
=======================================================================
Clock Generator Speed JP7 JP8
--------------------------------------------
TK9207 33MHZ 1-2 1-2
40MHZ 2-3 1-2
--------------------------------------------
KTS0808C/0801C 40MHZ 1-2 1-2
AV9107 50MHZ 2-3 1-2
--------------------------------------------
TK9307 25MHZ 1-2 1-2
33MHZ 2-3 1-2
40MHZ 1-2 2-3
50MHZ 2-3 2-3 JP24
-----------------------------------------------------
PhaseLink 25MHZ 2-3 1-2 1-2
PLL52C05 33MHZ 2-3 2-3 1-2
KTS KDN-802 40MHZ 1-2 1-2 2-3
50MHZ 2-3 1-2 2-3
=======================================================================
Cache| C A C H E M E M O R Y | TAG RAM
Size | U22 U23 U24 U25 U29 U30 U31 U32 | U21 U28
----------------------------------------------------------------------
64K | 8Kx8 8Kx8 8Kx8 8Kx8 8Kx8 8Kx8 8Kx8 8Kx8 | 8Kx8 -----
128K | 32Kx8 32Kx8 32Kx8 32Kx8 ---- ---- ---- ---- | 8Kx8 -----
256K | 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 | 8Kx8 8Kx8
256K | 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 32Kx8 | 32Kx8 -----
Cache JP2 JP3 JP4 JP5 JP6
--------------------------------------------
64K OPEN 1-2 OPEN 1-2 OPEN
128K OPEN 1-2 1-2 2-3 2-3
256K 1-2 1-2 1-2 1-2 1-2
Dobrze rozumiem ze nie mozna puscic na tej plycie DX2-80 ?
Pozdrawaim
Tomek Dębiński
tdebinski_at_poczta.onet.pl
http://tdebinski.republika.pl
Pozdrawiam
Tomek Dębiński
tdebinski_at_poczta.onet.pl
http://tdebinski.republika.pl
To archiwum zostało wygenerowane przez hypermail 2.1.7 : Wed 19 May 2004 - 01:09:03 MET DST